Networking with Windows Server 2016
Question No: 1
Your network contains an Active directory forest named contoso.com. The forest has a Distributed File System (DFS) namespace named \\contoso.com\namespace1.
The domain contains a file server named Server1 that runs Windows Server 2016. You create a folder named Folder1 on Server1.
Which two cmdlets should you use? Each correct answer presents part of the solution.
NOTE: Each correct selection is worth one point.
Question No: 2
A company named Contoso, Ltd has five Hyper-V hosts that are configured as shown in the following table.
What are two valid live migration scenarios for virtual machines in your environment?
from Sever1 to server5
from Server4 to Server 5
from Server2 to Server3
from Server3 to Server4
Question No: 3
Your company owns the public Internet IP address range of 184.108.40.206 to 220.127.116.11.
You need to create a subnet that supports four hosts. The solution must minimize the number of addresses available to the subnet.
Which subnet should you use?
A. 18.104.22.168/28 B. 22.214.171.124/30 C. 126.96.36.199/29
D. 188.8.131.52 with subnet mask 255.255.255.224
Answer: C Explanation:
Question No: 4
You have a server named Server1 that runs Windows Server 2016. Server1 has the following routing table.
What will occur when Server1 attempts to connect to a host that has an IP address of 172.20.10.50?
Server1 will attempt to connect directly to 172.20.10.50.
Server1 will route the connection to 10.10.0.2.
Server1 will silently drop the connection attempt.
Server1 will route the connection to 192.168.2.1.
Answer: D Explanation:
Question No: 5
Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
Your network contains an Active Directory domain named contoso.com. The domain
contains a DNS server named Server1. All client computers run Windows 10. On Server1, you have the following zone configuration.
You have the following subnets defined on Server1.
You need to prevent Server1 from resolving queries from DNS clients located on Subnet4. Server1 must resolve queries from all other DNS clients.
Solution: From Windows Firewall with Advanced Security on Server1, you create an inbound rule.
Does this meet the goal?
Answer: B Explanation:
Question No: 6
Note: This question is part of a series of questions that use the same scenario. For your convenience, the scenario is repeated in each question. Each question presents a different goal and answer choices, but the text of the scenario is exactly the same in each question in this series.
Your network contains an Active Directory domain named contoso.com. The functional level of the domain is Windows Server 2012.
The network uses an address space of 192.168.0.0/16 and contains multiple subnets. The network is not connected to the Internet.
The domain contains three servers configured as shown in the following table.
Client computers obtain TCP/IP settings from Server3.
You add a second network adapter to Server2. You connect the new network adapter to the Internet. You install the Routing role service on Server2.
Server1 has four DNS zones configured as shown in the following table.
You need to ensure that when a record is added dynamically to fabrikam.com, only the computer that created the record can modify the record. The solution must allow administrators to modify all of the records in fabrikam.com.
What should you do?
Change fabrikam.com to an Active Directory-integrated zone.
Raise the functional level of the domain.
Modify the security settings of the Fabrikam.com.dns file.
Modify the Start of Authority (SOA) settings of fabrikam.com
Answer: A Explanation:
Question No: 7
Note: This question is part of a series of questions that use the same or similar answer choices. An answer choice may be correct for more than one question in the series. Each question is independent of the other questions in this series. Information and details provided in a question apply only to that question.
You have a DHCP server named Server1 that has three network cards. Each network card is configured to use a static IP address.
You need to prevent all client computers that have physical address beginning with 98-5F from leasing an IP address from Server1.
What should you do?
From the properties of Scope1, modify the Conflict detection attempts setting.
From the properties of Scope1, configure Name Protection.
From the properties of IPv4, configure the bindings.
From IPv4, create a new filter.
From the properties of Scope1, create an exclusion range.
From IPv4, run the DHCP Policy Configuration Wizard.
From Control Panel, modify the properties of Ethernet.
From Scope1, create a reservation.
Question No: 8 HOTSPOT
Your network contains an Active Directory forest named contoso.com. The forest has three sites named Site1, Site2 and Site3.
Distributed File System (DFS) for the forest is configured as shown in the exhibit.
The forest contains a server named Server2 that hosts the DFS namespace.
\\Contoso.com\Namespace1\Folder2 has the following configuration.
\\Contoso\Namespace1\Folder2 has the targets configured as shown in the following table.
For each of the following statement, Select Yes if Statement is true. Otherwise , select No.
Explanation: Yes gt; Nogt;No
Question No: 9 HOTSPOT
Your network contains an Active Directory domain named contoso.com. The domain contains two servers named Server1 and Server2 that run Windows Server 2016.
Server1 has Microsoft System Center 2016 Virtual Machine Manager (VMM) installed. Server2 has IP Address Management (IPAM) installed.
You create a domain user named User1.
You need to integrate IPAM and VMM. VMM must use the account of User1 to manage IPAM. The solution must use the principle of least privilege.
What should you do on each server? To answer, select the appropriate options in the answer area.
On Server1: Create a Run As Account that uses User1. On Server2: Add User1 to IPAM ASM Administrator Role.
Question No: 10
You have a server named Server1 that runs Windows Server 2016. Server1 is a Hyper-V host that hosts a virtual machine named VM1.
Server1 has three network adapter cards that are connected to virtual switches named vSwitch1, vSwitch2 and vSwitch3.
You configure NIC Teaming on VM1 as shown in the exhibit. (Click the Exhibit button.)
You need to ensure that VM1 will retain access to the network if a physical network adapter card fails on Server1.
What should you do?
From Windows PowerShell on VM1, run the Set-VmNetworkAdapterTeamMapping
From Windows PowerShell on Server1, run the Set-VmNetworkAdapter cmdlet.
From Windows PowerShell on Server1, run the Set-VmSwitch cmdlet.
From Windows PowerShell on Server1, run the Set- VmNetworkAdapterFailoverConfiguration cmdlet
|Lowest Price Guarantee||Yes||No||No|
|Free VCE Simulator||Yes||No||No|