[Free] 2018(Jan) EnsurePass Pass4sure Juniper JN0-343 Dumps with VCE and PDF 101-110

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-343.html

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 101 – (Topic 2)

You just implemented RSTP in your Layer 2 network. Which two statements are true? (Choose two.)

  1. Switch ports in the alternate port role operating in indirect-recovery mode can immediately transition to the root port role and forwarding state when a failure occurs without waiting for the timer to expire.

  2. Switch ports in the alternate port role operating in shared mode can immediately transition to the root port role and forwarding state when a failure occurs without waiting for the timer to expire.

  3. Switch ports in the alternate port role operating in point-to-point mode can immediately transition to the root port role and forwarding state when a failure occurs without waiting for the timer to expire.

  4. Switch ports operating as edge ports automatically transition to the forwarding state, even directly after a failure and recovery scenario.

Answer: C,D

Question No: 102 – (Topic 2)

What does the attach bit in an IS-IS PDU indicate?

  1. The L1/L2 router is exporting a default route into the area.

  2. The L1/L2 router has reachability information to another IS-IS area.

  3. C. The L1/L2 router is sending information from Level 2 towards Level 1.

  4. The L1/L2 router is sending information from Level 1 towards Level 2.

Answer: B

Question No: 103 – (Topic 2)

What is one benefit of the root protection feature?

  1. It guards against loops caused by unidirectional link failures.

  2. It ensures downstream switches never become the root bridge.

  3. It disables the port when it detects that a loop has formed over an edge port.

  4. It guards against loops caused by a changed root bridge ID.

Answer: B

Question No: 104 – (Topic 2)

Which two link-state advertisement (LSA) types are allowed in a stub area? (Choose two.)

  1. LSA Type 1

  2. LSA Type 2

  3. LSA Type 4

  4. LSA Type 5

Answer: A,B

Question No: 105 – (Topic 2)

At which configuration hierarchy level is a static bridge table entry configured?

  1. [ interfaces interface-name ]

  2. [ protocols ]

  3. [ ethernet-switching-options ]

  4. [ forwarding-options ]

Answer: C

Question No: 106 – (Topic 2)

Which configuration is used to send and receive untagged packets through a trunk port?

Ensurepass 2018 PDF and VCE

  1. Option A

  2. Option B

  3. Option C

  4. Option D

Answer: B

Question No: 107 – (Topic 2)

You run the operational-mode command show ospf neighbor and notice that an expected OSPF neighbor on a broadcast link is not detected. Which three issues cause this behavior? (Choose three.)

  1. A problem exists with the physical link or Data Link Layer connectivity.

  2. The router IDs on the two devices do not match.

  3. The IP subnet mask does not match on each end of the link.

  4. The area type does not match on each end of the link.

  5. The AS number on the two devices do not match.

Answer: A,C,D

Question No: 108 – (Topic 2)

You configured an aggregate route of 192.168.8.0/21 and committed the updated configuration. Using an operational show command, you notice that the newly configured route is not present in the output. What would explain this behavior?

  1. The next hop is not resolvable.

  2. The next hop is not reachable.

  3. There are no active contributing routes.

  4. An aggregate route will not show up in the local table; it will be shared only with BGP neighbors.

Answer: C

Question No: 109 – (Topic 2)

What is a requirement for link aggregation?

  1. Member links must be on continuous ports.

  2. Member links must be on the same switch in a Virtual Chassis.

  3. The speed of the member links must be the same.

  4. LACP must be configured.

Answer: C

Question No: 110 – (Topic 2)

Which misconfiguration would cause an OSPF neighbor ship to be stuck in an ExStart state?

  1. authentication mismatch

  2. timer mismatch

  3. subnet mismatch

  4. MTU mismatch

Answer: D

100% Ensurepass Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-343 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.