[Free] 2018(Jan) EnsurePass Pass4sure Juniper JN0-343 Dumps with VCE and PDF 121-130

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-343.html

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 121 – (Topic 2)

Ensurepass 2018 PDF and VCE

In the exhibit, you run the command show ospf neighbor on R3 and notice that an adjacency with R5 remains in the 2-Way state. Which statement is true?

  1. A problem exists with the physical link or Data Link Layer connectivity.

  2. The area type does not match on each end of the link.

  3. The IP MTU does not match on each end of the link.

  4. This output is normal in this configuration.

Answer: D

Question No: 122 – (Topic 2)

An operator can use the show vlans command with no options to determine which two of the following? (Choose two.)

  1. Interfaces belonging to a VLAN

  2. Link up or down status of an interface belonging to a VLAN

  3. Known MAC addresses associated with a VLAN

  4. IP address of the RVI associated with a VLAN

Answer: A,B

Question No: 123 – (Topic 2)

BGP is best described as what type of routing protocol?

  1. link state

  2. distance vector

  3. path state

  4. path vector

Answer: D

Question No: 124 – (Topic 2)

Ensurepass 2018 PDF and VCE

As shown in the exhibit, three switches are connected and participating in RSTP. Switch

-1 was elected the root bridge and Switch-2 has a lower-cost path to the root bridge than Switch-3. Based on the details provided, which three statements are correct? (Choose three.)

  1. Switch-3#39;s ge-0/0/10.0 port assumes the alternate role and blocking state.

  2. Switch-3#39;s ge-0/0/10.0 port assumes the designated role and forwarding state.

  3. Switch-2#39;s ge-0/0/10.0 port assumes the designated role and forwarding state.

  4. Switch-1#39;s ports all assume the root port role and the forwarding state.

  5. Switch-1#39;s ports all assume the designated port role and the forwarding state.

Answer: A,C,E

Question No: 125 – (Topic 2)

You want to ensure that interface routes appear in multiple routing instances. Which configuration accomplishes this scenario?

  1. Configure each interface under multiple routing instances.

  2. Add an import policy for each routing instance.

  3. Configure the routing instance to be a forwarding type instead of a virtual-router type.

  4. Configure a RIB group and configure the router to install interface routes in the RIB group.

Answer: D

Question No: 126 – (Topic 2)

By default, which VLAN ID value is associated with the default VLAN on EX Series switches?

  1. 0

  2. 1

  3. 32

D. 255

Answer: A

Question No: 127 – (Topic 2)

Ensurepass 2018 PDF and VCE

Based on the topology and configurations shown in the exhibit, which two statements are true? (Choose two.)

  1. Switch-3 will be elected the root bridge.

  2. Both of Switch-1#39;s interfaces will assume the forwarding state.

  3. Switch-2 will be elected the root bridge.

  4. Both of Switch-3#39;s interfaces will assume the forwarding state.

Answer: C,D

Question No: 128 – (Topic 2)

On which interface would an IP address be configured for a routed VLAN interface?

A. ge-0/0/20.100

  1. vlan.100

  2. rvi.100

  3. l3-interface.100

Answer: B

Question No: 129 – (Topic 2)

On an edge router, you want to create a default route with a next hop to an external connection. The route should be available only when you are receiving routes from the external provider. Which type of route would you configure on your device to accomplish this objective?

  1. an aggregate route

  2. a generated route

  3. a primary contributing route

  4. a static route

Answer: B

Question No: 130 – (Topic 2)

Ensurepass 2018 PDF and VCE

As shown in the exhibit, you recently installed four EX Series switches in your network. These switches are using the default RSTP configuration. Which two statements are correct? (Choose two.)

  1. Switch-4 selects ge-0/0/10.0 as its root port.

  2. Switch-4 selects ge-0/0/9.0 as its root port.

  3. Switch-4#39;s root cost path is 4000.

  4. Switch-4#39;s root cost path is 40000.

Answer: B,D

100% Ensurepass Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-343 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.