[Free] 2018(Jan) EnsurePass Pass4sure Juniper JN0-343 Dumps with VCE and PDF 141-150

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-343.html

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 141 – (Topic 2)

Which BGP attribute is used to influence inbound traffic when two peering sessions to the same AS exist?

  1. weight

  2. local preference

  3. router ID

  4. MED

Answer: D

Question No: 142 – (Topic 2)

Which three types of firewall filters are supported on EX Series switches? (Choose three.)

  1. router filters

  2. switch filters

  3. source filters

  4. VLAN filters

  5. port filters

Answer: A,D,E

Question No: 143 – (Topic 2)

What is a benefit of the 802.3ad standard?

  1. loop detection

  2. security

  3. higher bandwidth

  4. strict queuing

Answer: C

Question No: 144 – (Topic 2)

You have altered the factory-default storm control configuration so that interfaces on which the storm control level is exceeded are temporarily shut down for five minutes. Which two methods can you use to monitor that the auto recovery feature is working? (Choose two.)

  1. Issue the monitor traffic violations command.

  2. Issue the monitor start messages command.

  3. Issue the show storm-control violations command.

  4. Issue the show ethernet-switching interfaces command.

Answer: B,D

Question No: 145 – (Topic 2)

How many untagged VLANs can be configured on an EX Series switch port?

  1. 0

  2. 1

C. 4095

D. 4096

Answer: B

Question No: 146 – (Topic 2)

You just installed Switch-1 and Switch-2 in your network. Both switches are EX Series switches and are connected to each other using a Layer 2 switch port. Switch-1 must run STP, whereas Switch-2 must run RSTP. Given the scenario, which statement is true?

  1. The two switches communicate using RSTP.

  2. The two switches will not communicate using STP or RSTP.

  3. The two switches communicate using STP.

  4. The two switches run in dual-mode and communicate using STP and RSTP.

Answer: C

Question No: 147 – (Topic 2)

What are two switch port default settings on EX Series switches? (Choose two.)

  1. Set as trunk mode.

  2. Set with VLAN ID 0.

  3. Set with the native VLAN.

  4. Set as access mode.

Answer: B,D

Question No: 148 – (Topic 2)

You have a route in the inet.0 routing table that has four valid physical next hops assigned to it. Which event prompts an update to the information in the forwarding table for this particular route?

  1. When a new physical next hop is added to the next-hop set.

  2. When any configuration change is committed on the router.

  3. When a packet is forwarded towards the route destination.

  4. When an additional route of the same IP address class is added to inet.0.

Answer: A

Question No: 149 – (Topic 2)

Which three configurations are required for an operational routed VLAN interface (RVI)? (Choose three.)

  1. {master:0}[edit]

    user@ex# show ethernet-switching vlan-map vlan-id 10;

    interface { ge-0/0/1.0;

    }

  2. {master:0}[edit]

    user@ex# show interfaces ge-0/0/1 unit 0 {

    family ethernet-switching;

    }

  3. {master:0}[edit]

    user@ex# show interfaces vlan.10 family inet {

    address 192.168.10.1/24;

    }

  4. {master:0}[edit]

    user@ex# show interfaces rvi.1 interface {

    ge-0/0/1.0;

    }

  5. {master:0}[edit] user@ex# show vlans v10 vlan-id 10;

interface { ge-0/0/1.0;

} l3-interface vlan.10;

Answer: B,C,E

Question No: 150 – (Topic 2)

A switch port is sending both tagged and untagged traffic. What is its possible configuration?

  1. {master:0}[edit interfaces ge-0/0/0] user@switch# show

    unit 0 {

    family ethernet-switching { port-mode access;

    vlan { members data;

    }

    }

    }

  2. {master:0}[edit interfaces ge-0/0/0] user@switch# show

    unit 0 {

    family ethernet-switching { port-mode trunk;

    vlan { members data;

    }

    }

    }

  3. {master:0}[edit interfaces ge-0/0/0] user@switch# show

    unit 0 {

    family ethernet-switching { port-mode access;

    vlan { members data;

    }

    native-vlan-id data;

    }

    }

  4. [edit ethernet-switching-options] user@switch# show

voip { interface all;

vlan voiceVLAN;

forwarding-class expedited-forwarding;

}

}

[edit vlans] user@switch# show voiceVLAN {

vlan-id 3;

}

}

[edit interfaces] user@switch# show ge-0/1/1 {

unit 0 {

family ethernet-switching { port-mode access;

}

}

}

Answer: D

100% Ensurepass Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-343 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.