[Free] 2018(Jan) EnsurePass Pass4sure Juniper JN0-343 Dumps with VCE and PDF 31-40

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-343.html

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 31 – (Topic 1)

An administrator finds that traffic from a large file download over an HTTP session is not load-balanced across multiple links in a LAG. What is the possible cause?

  1. Per-packet load-balancing is not configured.

  2. The redundant path has a different IGP metric.

  3. The hash key is not configured in the forwarding-options stanza.

  4. This is the expected behavior.

Answer: D

Question No: 32 – (Topic 1)

When the DF bit is set, which two actions will a router perform by default on a packet that is larger than the MTU of the interface? (Choose two.)

  1. The router drops the packet.

  2. The router sends an ICMP MTU exceeded message to the source.

  3. The router fragments and forwards the packet.

  4. The router generates a syslog message indicating that a packet was dropped due to the exceeded MTU.

Answer: A,B

Question No: 33 – (Topic 1)

What is the default value of the link-state advertisement (LSA) refresh timer in the Junos OS?

  1. 10 minutes

  2. 30 minutes

  3. 50 minutes

  4. 60 minutes

Answer: C

Question No: 34 – (Topic 1)

Which two statements are true regarding a designated intermediate system (DIS) in an IS- IS network? (Choose two.)

  1. It performs a similar role to the designated router (DR) in OSPF.

  2. It is not allowed to send any PDUs on a designated intermediate system (DIS).

  3. A backup DIS is not elected.

  4. DIS selection uses the router#39;s IP address as a tiebreaker.

Answer: A,C

Question No: 35 – (Topic 1)

Ensurepass 2018 PDF and VCE

Given the attached exhibit, what will happen to traffic sourced from 192.168.1.100 and destined to 172.16.1.69/32?

  1. It will use the default route.

  2. It will be routed to 10.17.0.1.

  3. It will be routed to 10.32.0.1.

  4. It will be dropped.

Answer: C

Question No: 36 – (Topic 1)

Given that ge-0/1/1 is set up as a trunk port, which command set will NOT successfully set the trunk to carry VLANs 10 and 11?

  1. set interfaces ge-0/1/1.0 family ethernet-switching vlan members [Vlan10 Vlan11]

  2. set interfaces ge-0/1/1.0 family ethernet-switching vlan members Vlan10 members Vlan11

  3. set interfaces ge-0/1/1.0 family ethernet-switching vlan members Vlan10,Vlan11

  4. set interfaces ge-0/1/1.0 family ethernet-switching vlan members Vlan10set interfaces ge-0/1/1.0 family ethernet-switching vlan members Vlan11

Answer: C

Question No: 37 – (Topic 1)

A network with five switches has been configured to run Rapid Spanning Tree Protocol (RSTP) with default settings. How many seconds does it take to detect a failure between two neighboring switches?

  1. 2 seconds

  2. 3 seconds

  3. 6 seconds

  4. 15 seconds

Answer: C

Reference: Page 3-14 of the JNCIS-ENT Routing Study Guide – quot;As previously mentioned, STP uses BPDUs to elect a root bridge, identify root ports for each switch, identify designated ports foreach physical LAN segment, prune specific redundant links to create a loop-free tree topology, and report and acknowledge topology changes. RSTP configuration BPDUs also function as keepalives. All RSTP bridges send configuration BPDUs every 2 seconds by default. You can alter this value, if necessary.quot;

Question No: 38 – (Topic 1)

Which side of the OSPF router initiates the database description exchange?

  1. the side with the higher IP address

  2. the side with the higher router ID

  3. the side with the higher priority

  4. the side with the higher uptime

Answer: B

Question No: 39 – (Topic 1)

Which configuration summarizes external routes in the 172.16.0.0/22 range into a single prefix on an ABR for Area 1?

  1. protocols { ospf {

    area 0.0.0.1 { nssa { default-lsa {

    default-metric 1;

    metric-type 1;

    }

    }

    area-range 172.16.0.0/22;

    }

    }

    }

  2. protocols { ospf {

    area 0.0.0.1 { nssa {

    area-range 172.16.0.0/22;

    }

    }

    }

    }

  3. protocols {

    ospf {

    area 0.0.0.1 { stub summaries;

    }

    }

    }

  4. protocols { ospf {

area 0.0.0.1 { nssa;

area-range 172.16.0.0/22 restrict;

}

}

}

Answer: B

Question No: 40 – (Topic 1)

Which statement about LACP is true?

  1. LACP is enabled by default on aggregated Ethernet interfaces.

  2. LACP is enabled by default on redundant trunk groups.

  3. The default mode of operation of an LACP interface is passive.

  4. At least one side of an LACP session must be configured as passive.

Answer: C

100% Ensurepass Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-343 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.