[Free] 2018(Jan) EnsurePass Pass4sure Juniper JN0-533 Dumps with VCE and PDF 51-60

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-533
100% Free Download! 100% Pass Guaranteed!

FWV, Specialist (JNCIS-FWV)

Question No: 51

On a ScreenOS device, which word appears at the beginning of configuration commands?

  1. set

  2. configure

  3. enable

  4. commit

Answer: D

Question No: 52

You want to ensure that the ScreenOS device sends alert data to notify the security operation center.Which three log destinations would you set to accomplish your objective? (Choose three.)

  1. e-mail

  2. SNMP

  3. console

  4. internal

  5. syslog

Answer: A,B,E

Question No: 53

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Network traffic with a source IP of, destination IP of, and a destination port of 80 is sent through the ScreenOS device. The inbound zone is Trust, the outbound zone is Untrust.

Based on the policy configuration shown in the exhibit, what happens to this traffic?

  1. The traffic is denied by default policy.

  2. Traffic is denied by policy ID 3.

  3. Traffic is permitted by the global policy.

  4. Traffic is permitted by policy ID 2.

Answer: C

Question No: 54

– Exhibit –

ssg5(M)-gt; get conf | incl ethernet1/2

set interface quot;ethernet1/2quot; zone quot;Untrustquot; set interface ethernet1/2 ip set interface ethernet1/2 route

set interface quot;ethernet1/2quot; description quot;Internet Connection 1quot; set interface ethernet1/2 ip manageable

set interface ethernet1/2 manage ping

– Exhibit –

You need to add a DIP pool to the interface shown in the exhibit. The DIP pool has been assigned the IP addresses through

Which command would you use to accomplish this task?

A. set interface ethernet1/2 ext ip dip 1

B. set interface ethernet1/2 ext ip dip 1

C. set interface ethernet1/2 dip 1

D. set interface ethernet1/2 secondary ip dip 1

Answer: A

Question No: 55

– Exhibit –

SSH V2 is active ns5gt-gt; get int et1 Interface ethernet1: description ethernet1

number 2, if_info 176, if_index 0, mode nat link up, phy-link up/full-duplex

status change:1, last change:02/06/1997 18:02:32 vsys Root, zone Trust, vr trust-vr

dhcp client disabled PPPoE disabled

admin mtu 0, operating mtu 1500, default mtu 1500


*manage ip, route-deny disable

pmtu-v4 disabled

ping enabled, telnet enabled, SSH enabled, SNMP enabled web enabled, ident-reset disabled, SSL enabled

SSH is enabled

SSH is ready for connections Maximum sessions: 3

Active sessions: 3

– Exhibit –

You are the administrator of a NetScreen 5GT. The system administrator cannot use SSH to log in to the NetScreen 5GT.Referring to the exhibit, what is the problem?

  1. Interface eth1 does not permit logins using SSH.

  2. SSH is not enabled on the NetScreen 5GT.

  3. Interface eth1#39;s link status is down.

  4. The maximum SSH session has been used.

Answer: D

Question No: 56

You manage a ScreenOS device. A user complains that the FTP download speed is slow. You suspect a cable or an interface might be the problem.

Which command provides interface error information?

  1. show counter flow interface

  2. get counter flow interface

  3. show counter statistics interface

  4. get counter statistics interface

Answer: D

Question No: 57

What are two advantages for using the count parameter on a security policy? (Choose two.)

  1. to see any NAT traffic drops for that policy

  2. to see how many times users log in to the ScreenOS device

  3. to count the total number of bytes of traffic for that policy

  4. to see if the policy is temporarily not being used

Answer: C,D

Question No: 58

When a new session is created on the primary ScreenOS device, what are two results that happen on the backup device? (Choose two.)

  1. Session information is sent in real time from the master to the backup over the HA link.

  2. Session update messages are bundled together and sent over every 10 seconds to the backup over the HA link.

  3. A session is created on the backup device with a timeout value of 8 times the default.

  4. A session is created on the backup device and is completely identical to that of the master#39;s session.

Answer: A,C

Question No: 59

Which two protocols are used for NSRP IP tracking? (Choose two.)

  1. ARP

  2. TCP

  3. UDP

  4. ICMP

Answer: A,D

Question No: 60

You want to centralize the logging for all your ScreenOS devices and you must be able to synchronize the log.Which two actions would you perform to accomplish this? (Choose two.)

  1. Enable logging to the console.

  2. Enable logging to syslog.

  3. Enable NTP and set to UTC/GMT time.

  4. Enable logging to the USB.

Answer: B,C

100% Ensurepass Free Download!
Download Free Demo:JN0-533 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-533 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.