[Free] 2018(Mar) EnsurePass Braindumps Cisco 300-180 Dumps with VCE and PDF 41-50

Ensurepass.com : Ensure you pass the IT Exams
2018 Mar Cisco Official New Released 300-180
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco Data Center Infrastructure

Question No: 41 – (Topic 1)

Which protocols can be used to send to Cisco TAC (Technical Assistance Center) the show tech-support command output information about the Cisco UCS domain? (Choose two.)

  1. TFTP

  2. FTP

  3. SCP

  4. Telnet

  5. SecureTelnet

Answer: B,C

Question No: 42 – (Topic 1)

You attempt to perform an ESXi update on a Cisco UCS C250 server, but the update does not recognize the NICs. You must perform the update as quickly as possible. Which step must you do first?

  1. Check the UCS compatibility matrix and replace the NIC with a supported one.

  2. Reconfigure the NIC ID on the LOM.

  3. Update the LOM firmware by using the Cisco Host Update Utility.

  4. Update the NIC firmware by using the Cisco Host Update Utility.

Answer: C

Question No: 43 – (Topic 1)

Which logs are used to troubleshoot hardware failure?

  1. system event log

  2. audit log

  3. accounting log

  4. gateway logs

  5. system log

Answer: A

Question No: 44 – (Topic 1)

Which option describes why the service profiles do not inherit changes from the template?

  1. The service profile is not compatible with the changes.

  2. The changes to the template have not been committed.

  3. It is an initial template.

  4. The service profile has disabled inheritance.

Answer: C

Question No: 45 – (Topic 1)

Which statement is true about system event logs?

  1. By default, they require manual clearing.

  2. They report operating system crashes and errors.

  3. They are also referred to as system error logs.

  4. They can only be accessed from Cisco UCS Manager.

Answer: A

Question No: 46 – (Topic 1)

Which four tasks can be performed via Cisco IMC remote access to a Cisco UCS system? (Choose four.)

  1. power cycle the server

  2. deploy an operating system

  3. toggle the locator LED

  4. configure the boot order

  5. view properties and sensors

  6. configure the hypervisor

  7. enable Cisco UCS Manager

Answer: A,C,D,E

Question No: 47 – (Topic 1)

Which Cisco UCS C Series command sequence initiates the sending of a technical support file to a TFTP server?

  1. ucs /cimc # scope tech-support ucs /cimc/tech-support # set ip ucs /cimc/tech- support *# set tftp-path \showtechsupport ucs /cimc/tech-support *#commit ucs /cimc/tech- support *#start

  2. ucs /cimc # scope tech-support ucs /cimc/tech-support # set tftp-ip ucs

    /cimc/tech-support *# set path \showtechsupport ucs /cimc/tech-support *#commit ucs

    /cimc/tech-support *#start

  3. ucs /cimc # scope support ucs /cimc/support # set tftp-ip ucs /cimc/support *# set path \showtechsupport ucs /cimc/support *#commit ucs /cimc/support *#start

  4. ucs /cimc # scope system-support ucs /cimc/system-support # set tftp-ip ucs

/cimc/system-support *# set path \showtechsupport ucs /cimc/system-support *#commit

ucs /cimc/system-support *#start

Answer: B

Question No: 48 – (Topic 1)

UCS-A# scope eth-uplink

UCS-A /eth-uplink # scope fabric a

UCS-A /eth-uplink/fabric # scope interface 2 3

UCS-A /eth-uplink/fabric/interface # create mon-src Monitor23 UCS-A /eth-uplink/fabric/interface/mon-src* # set direction receive UCS-A /eth-uplink/fabric/interface/mon-src* # commit-buffer

What does the command scope interface 2 3 in the above CLI command sequence do on a Cisco UCS blade server?

  1. enters the interface command mode for the specified uplink port

  2. enters the interface command mode for the specified Fabric A

  3. enters the interface command mode for the specified Fabric B

  4. enters slot 3 port 2 specified uplink port

Answer: A

Question No: 49 – (Topic 1)

Which of these does not have an FSM associated with it?

  1. vCenter connection

  2. service profile

  3. server hardware

  4. service profile templates

Answer: D

Question No: 50 – (Topic 1)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

In a Cisco UCS environment, which switch mode does the exhibit portray?

  1. end host mode

  2. switching mode

  3. access mode

  4. core mode

Answer: A

100% Ensurepass Free Download!
Download Free Demo:300-180 Demo PDF
100% Ensurepass Free Guaranteed!
300-180 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.